7601P22360 Maytag Range/Stove/Oven Timer Repair |
Failure codes, problems, and resolutions for Maytag timer model # 7601P22360 |
![Maytag ERCs and Maytag stove clocks and timers]() |
Manufacturer : |
Maytag |
| Part Number : |
7601P22360 |
| Appliance Type : |
Range/Stove/Oven |
| Color : |
|
| Description : |
Electronic Range/Oven Timer |
|
Do you have a failed Maytag 7601P22360 timer?
Click here:
We can repair or replace your faulty 7601P22360 timer. |
![Request Appliance Timer Service]() |
Recent Service Requests for Maytag Part Number 7601P22360| City | Model Number | Failure Code | Problem Description | Resolution |
|---|
| Toronto, Ontario | CRE9500 ADW | None | Oven runs 100 F below set point. Temp sensor was checked with ohm meter and it has a expected resistance at RT and boiling water temp. | Repaired | | St-Léonard, Quebec | CRE 9500 ADW SERIE 11 | F-5 | Howards has all the details | Awaiting receipt of timer | | Hamilton, Ontario | CRE9600ADW | F2 | After stove has been powered on (18 - 36 hours) the F2 code is displayed (it will come on with no elements or oven turned on). replaced temp sensor on spec but still same problem. Turn power off at breaker leave off for 8 hours then turn on and will work for 18 - 36 hours before code comes up and stove alarms | Repaired | | Chemainus, British Columbia | CRE8700AOL | N/A | alarm /buzzer will not stop | Repaired | | Lindsay, Ontario | | none | Not able to maintain accurate temp, sensor ch OK | Repaired | | Hammonds Plains, Nova Scotia | CRE9500ADW | N/A | Oven temperature does not come up to selected temperature. Oven heats up to approximately 120 degrees lower than selected temperature (if control is turned up to 350 degrees oven heats up to 230 degrees). Tried replacing temperature sensor already with no success. | Awaiting receipt of timer | | Port Carling, Ontario | CRE9700ADB | none | Turn oven on and temperature immediately shows as high number Eg 345*. Oven does not heat up. Checked oven sensor, reads same as new sensor. No failure code.
If unrepairable send back with remanufactured unit. | Awaiting receipt of timer | | Mississauga, Ontario | CRE9600ADW | No failure code | Oven temp does not reach display temp. Set to 350, actual temp is approx 200. confirmed with "Fluke" temp sensor. Temp probe tested and reads 1100 at room temp. Upper & Lower elements read approx. 20 ohms. 240v reaching both elements, all fuses ok. | Awaiting receipt of timer | | COPLAY, Pennsylvania | CRE9830BCE | F1 | oven stays on - can only turn off from electrical panel | Awaiting receipt of timer | | Penticton, British Columbia | CRE9600ADW | none | incorrect oven temperature. If I set at 350 the oven only heats to 150....if set at 550 the oven will heat to 350.
We have checked the temp probe, its working fine. We have checked both elements and they are working fine.
no failure code ever came on. | Repaired | | BIBLE HILL, Nova Scotia | CRE9600ADL | N/A | oven will not heat. | Repaired | | BIBLE HILL, Nova Scotia | cre9500adw | N/A | oven will not heat | Repaired | | Etobicoke, Ontario | CRE9500ADW | FA | The timer continuously beeps when the oven is switched on by the oven main switch.It prevents the setting of the oven temperature as the display displays only "FO" | Beyond Repair | | Etobicoke, Ontario | CRE9500ADW | FA | Touch Pad Faulty | Beyond Repair | | Etobicoke, Ontario | CRE9500ADW | FA | The timer continuously beeps when the oven is switched on by the oven main switch.It prevents the setting of the oven temperature as the display displays only "FO" | Beyond Repair | | Etobicoke, Ontario | CRE9500ADW | FA | Touch Pad Faulty | Beyond Repair |
|
