ERC14500MC General Electric Range/Stove/Oven Timer Repair |
Failure codes, problems, and resolutions for General Electric timer model # ERC14500MC |
![General Electric (GE) ERCs and General Electric (GE) stove clocks and timers]() |
Manufacturer : |
General Electric |
| Part Number : |
ERC14500MC |
| Appliance Type : |
Range/Stove/Oven |
| Color : |
|
| Description : |
Electronic Range/Oven Timer |
|
Do you have a failed General Electric ERC14500MC timer?
Click here:
We can repair or replace your faulty ERC14500MC timer. |
![Request Appliance Timer Service]() |
Recent Service Requests for General Electric Part Number ERC14500MC| City | Model Number | Failure Code | Problem Description | Resolution |
|---|
| Burdett, New York | jtp 10gp2bg | na | Shuts off immediately with no heat or relay sound. | Beyond Repair | | Los Gatos, California | JTP10GS3BG | none | The oven temp is now too low by approx 100 deg F. ie to get the oven temp up to 350, you need to set teh temp to 450 deg F. I have replaced the temp probe and verifieds the 1100ohm continuity to the timer board. IO have measured continuity and resistance for teh bake coil and it is in spec at 21ohms. Was working fine until recently. Oven >20 yrs old. I would liek a reconditioned one if you have it, otherwise repair mine is OK. | Awaiting receipt of timer | | Sylvania, Ohio | JTP11WS3WG | None | Oven will only get up to 200 F. | Repaired | | Rangeley, Maine | jt1000dfbb | N/A | don't know, unit was pulled out of oven by some one else. | Repaired | | Lancaster, Pennsylvania | JTP10GP1BG | none | beyond repair. | Awaiting receipt of timer | | vincent, Alabama | jtp10gs | f1 ? | bottom element won't come on, has tested ok. seems to be contact on board?
serial number 41657 | Repaired | | Livermore, California | JTP 10GP3BG | N/A | It appears to control but at a temp about 250 degrees lower than the requisted temp. | Repaired | | st johns, Florida | jtp11ws2wg | f1 | Beeeeeep | Awaiting receipt of timer | | Greenland, Arkansas | JTP10GS2BG | none | Oven only heats up to about 200 degrees while steadily climbing to set temp (400) on the display. Some problems with BAKE button, requiring you to push it several (random number) of times to get it to start. | Repaired | | centennial, Colorado | JTP10GP3BG | none | Oven turns on but will not maintain set temperature. oven display says it has reached the set temperature, but in fact temp is well below that. | Repaired | | Granbury, Texas | JTP10GS2BG | N/A | The oven will not heat over 230F. It appears that Potter Brumfield relay T90H1D12-24-18 will not close. The timer may need repair, or the relay may need to be refurbished. | Repaired | | Broken Arrow, Oklahoma | JTP10GP3BG | None | No error codes. Only gets to about 200 degrees when baking. Self cleaning seemed to work OK. Oven sensor measures 1120 Ohms at room temperature. Talked with Howard on the phone and he felt sure it was the ERC that needed to be repaired. Bad timing my wife just sent in her State Fair Baking contest money. She wants a new oven. I can't afford that so I hope you folks can get me out of the dog house and back in the big house fast.
Thanks! | Repaired | | san diego, California | jtp11ws2wg | F1 | In the beginning pushing stop would cause F1 to appear each time you pushed stop until the fan stopped. Later the oven would stop working after it had been at temperature for some time. It could not be restarted until some time had elapsed. Finally one morning the fan was on, there was a constant beep and the oven was cold as expected as the oven should not have been on overnight. The full part number is erc-14500-mc/100-385-01 | Beyond Repair | | Anaheim, California | JTP 11WP3WG | F1 | Shows Error Code F1 and beeps can use to cook but after oven shut off error code returns and beeps again. must shut off main power to oven or will continue to beep. | Replaced with reconditioned timer | | jonesboro, Georgia | jtp10gs3bg | N/A | will not bake | Awaiting receipt of timer | | Los Gatos, California | JTP 10GP3BG | n/a | When setting BAKE, display changes to show curent oven temp, but never heats up. Display goes blank, and the oven is off. This was repeated with the same results each time. | Repaired | | Edisto Island, South Carolina | JTP 11WP3WG | N/A | Will not stay on thirty seconds. | Repaired | | SAN JOSE, California | JTP11WP3WG | no error code | Oven (bake mode) only heats to high temps (greater than 525+)
When the bake temp is set to 400 or 450, as in normal baking, the temperature only heats to 300 degrees or so.
I see no error codes. Keypad seems to work okay for all functions.
Cleaning and Broiling seem to work okay.
Just normal baking doesn't heat the oven hot enough.
I have tested the Sensor and the resistances seem to be in range:
1.1K: room-temp; 1.36K: boiling water; 1.06K: ice water;
I can also send copies (PDFs) of the wiring diagrams and technician data sheet if you need them. | Repaired |
|
